High crystalline silicon tempered glass solar spike Installation instructions

High crystalline silicon tempered glass solar spikeInstallation instructions

Established in 2006, “Shenzhen Luming Traffic Equipment Co., Ltd” was definited as an export-oriented high technology enterprise that specialize in solar traffic safety facilities’ R&D and sale over 10 years.

Our main products include: solar road studs, solar LED delineators, road reflectors, solar traffic safety signs, LED tunnel signs, traffic warning lights, solar traffic lights, anti-glare boards, solar LED anti-bump barriers, parking lot safety facilities etc. 

One, [size]: 100 * 100 * 50MM, light color yellow, white, red, green, blue species, surrounded by light.

Second, [installation location]: installed in the edge of the road, flashing at night to better enhance the road landscape, outline the outline of the road, the driver from the warning effect, to remind carefully driving.

Three, [material tools to prepare]: A glue (color transparent), B glue (color brown), white cement, scraper, chalk, tape, and plastic bucket, and glue stick, broom, the temperature below 10 degrees to prepare kerosene Furnace and other heating tools. Drilling and 105mm drill bits.

Fourth, [installation process]:

1, positioning: spike installation to smooth, dry and dry, clean, seamless.

2, mixed with plastic: spike special A glue, spike special B plastic, A plastic B glue ratio is 1: 1 (such as: A glue 1 kg, B glue is 1 kg), and then add 20% of the cement Fillers. Glue must be stirred evenly, consistent color.

3, perforation: hole in the hole in a good position in the hole, hole depth 3CM, the product height of 5CM, leaked the ground 2CM, buried 3CM (must punch the standard, or affect the product luminous intensity and service life) The

4 with glue: the ground clean, with plastic to be moderate, both stick to the bottom of the road signs, and do not spill too much, out of the plastic can be used scraper blowing, can be used repeatedly, stick to the surface of the product to clean the glue to avoid Luminous brightness, sticky after the left and right turn two, so that glue can be more uniform paste the ground and the road nail body.

5 tour: two hours after the installation of the spike should be checked again, the occurrence of crooked, should be reversed in time.

6 Road: must seal road 6 hours to ensure that the glue curing time.

Five [Note]:

1, traffic safety: construction personnel must be safe and reflective lighting, with anti-reflective roadblock facilities to block the construction area, the night construction of electronic light-emitting diversion card or warning lights and other signs to play a security warning effect.

2, do not install the spike on the marking, should be installed on the outside of the marking line from the mark 5cm.

3, each mixing glue shall not exceed 3 kg (because the glue after mixing in a certain period of time will be solidified, in order to avoid waste, do not mix gum each time more than 3 kg)

4, the temperature is less than 10 degrees, glue is not easy and dynamic, available kerosene furnace heating glue (heating A glue, B glue can not heat). Stir well with a stirrer.

5, in general, the spike with the same line of color, single-sided reflective film and the direction of the car relative, do not press the anti-crooked.

6, the installation process, do not glue the product to the surface of the product affect the luminous and beautiful.

7, the road with water can not be built.

Shenzhen LuMing Traffic Equipment Co., Ltd.

TEL:     0086 755 27708545

MOB:     0086  13925263646

FAX:     0086 755 27701581

EMAIL: szlm@szlmjt.com 

ADD: 3F, Building 1, Futing Industrial Zone, Guanlan Street, Longhua New District, Shenzhen

POST CODE: 518110

WEBSITES：

https://szlm9.1688.com/(China)

https://szlmjt.en.alibaba.com(English)